中文  |   English

联系我们

电话:0312-3013660

传真:0312-3013660

手机:18233233061

行业新闻
造型机故障检测之压头部分
造型机故障检测之压头部分
Indenter part of molding machine fault detection
造型机在使用一段时间后,压头可有能出现摆动动作迟钝、缓慢、应按下列方法进行造型机保养。
After the molding machine has been used for a period of time, the head can swing slowly and slowly, and the molding machine shall be maintained according to the following methods.
1、造型机故障检测时,检查造型机压头前后板间隙,是否有什么铁碴等异物阻碍,可清除后试车。
1. In the process of molding machine fault detection, check the gap between the front and rear plates of the molding machine indenter, and check whether there is any obstruction of foreign matters such as iron ballast, which can be removed before commissioning.
2、打开压头上后面两根进气管,操纵阀分别扳在原位与摆入,看看管口进气是否够大,如果进气量小也会造成压头摆动缓慢,造型机故障检测时,若是此原因可一直检查到操纵阀,直致空气滤清气,是否堵塞。
2. Open the two air intake pipes at the back of the head, turn the control valve to the original position and swing in respectively, and check whether the air intake at the pipe mouth is large enough. If the air intake is small, it will cause the head to swing slowly. During the fault detection of the molding machine, if this reason is found, check the control valve until the air is filtered and blocked.
3、造型机压头上面有盖板,打开观察齿条是否锈蚀严重,如果发生此造型机故障,同样会造成压头动作迟钝,可用煤油或汽油清洗即可。
3. There is a cover plate on the pressure head of the molding machine. Open it and observe whether the rack is seriously rusted. If this molding machine fails, the pressure head will also be sluggish. It can be cleaned with kerosene or gasoline.
4、造型机故障检测时,若上述情况都没发生,就应打开压头两侧法兰盘,检查齿条两侧Y型密封圈是否老化、变形,如是,也可造成压头缓慢。
4. In the process of molding machine fault detection, if none of the above occurs, the flange plates on both sides of the indenter shall be opened to check whether the y-rings on both sides of the rack are aged and deformed. If so, the indenter may be slow.
5、最后一招,打开位于造型机压头后上端法兰盘,检查齿轮轴承的黄油是否变质,如果是这样,可用煤油或汽油冲洗,同时搬动压头,会感觉越来越松。
5. Finally, open the flange at the upper end behind the pressure head of the molding machine, and check whether the grease of the gear bearing is deteriorated. If so, wash it with kerosene or gasoline, and move the pressure head at the same time, it will feel more and more loose
  1. 电话:0312-3013660
  2. 传真:0312-3013660
  3. 手机:18233233061
  4. 备案号:冀ICP备18002375号

版权 © 保定市乐通机械设备科技有限公司  推荐:垂直造型线,静压造型线,自动浇注机,半自动浇注机  网站制作:保定遨游公司